| Home |
| Remotes |
| Receivers |
| Keyless Entry and Wall Controls |
| Repair Parts |
| Universal (Almost) |
| NEW Tec Key Remotes |
| NEW Wayne Dalton Remotes & Keypads |
| Wireless Intercom System |
| Vehicle Alert System |
| TriCode® Remote Controls |
| Fingerprint Keyless Entry |
| Lubricant |
| Multi-Code 300 MHZ and International Freq. 40.685 MHz Frequency |
| Sky Link Security |
| Garage Accessories |
| Shipping/Returns |
| About Us |
| Customer Assistance |
| Coding Instr. |
| Fax or check Order form |
| Garage Door Monitor |
| Site Index |
 |
| Remotes |
 |
| Keyless Entry |
 |
| Repair Parts |
|
All orders are shipped same or next day!!! |
|
USPS Priority Mail 2-4 Business Days |
| VISA, Mastercard, American Express and Discover |
Wayne Dalton Garage Door Openers Quantum and Classic Drive models 3211, 3212, 3213, 3312, 3313, 3412, 3414, 3012, 3016, 3512 and 3514 Programming Instructions
Wayne Dalton Garage Door Opener 2 Button Mini Transmitter 299264
Warning!
During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury.
NEVER let children operate or play with door controls. Keep remote controls away from children. Fatal injury could result should a child become trapped between the door and the floor.
ALWAYS keep moving door in sight and away from people and objects until it is completely closed. To prevent serious injury or death, avoid standing in the open doorway or walking through while door is moving.
Security Code Change and Programming
NOTE: This transmitter is not compatible with the power heads with yellow antenna wires.
NOTE: The following steps describe the process to change the transmitter
security code and to program the transmitter.
IMPORTANT: You MUST change the transmitter security code prior to programming
the device to the power head unit.
Changing the Transmitter Code
Press and hold the button on the transmitter that you want to change (left
button or right button). The GREEN LED (light) will flash once then turn off.
Continue to hold the button until the GREEN LED begins to flash (approx. 10
Seconds).
When the GREEN LED flashes, immediately release the button and then immediately
press and hold the same button again. The GREEN LED will now come on steady.
Continue to hold the button until the GREEN LED begins to flash (approx. 5
seconds).
When the GREEN LED flashes, immediately release the button.
The code for this button has now been changes to a new randomly generated code.
Do not press the button again until instructed in “Programming Transmitter to
Motor Head Power Unit”.
You must now re-program this transmitter to the motor head unit. See
“Programming Transmitter to Motor Head unit” below.
Programming Transmitter to Power Head Unit
NOTE: Do not press any button on the transmitter until instructed.
1. Press the PROGRAM Switch button located on the garage door power head once.
The red PROGRAM STATUS light on the motor power head unit and overhead
Lamp will turn on and remain lit for one minute, indicating that it is ready to
learn the Transmitter.
2. Press the button on the Transmitter you wish to use to operate the door.
(NOTE:
For the 2-button transmitter this must be the same button that was used in
“Changing the Transmitter Code”). The PROGRAM STATUS light on the power head
will turn on and off three times indicating a successful.
3. Press the same button on the Transmitter once more to confirm operation. The
Opener will turn on and move the door.
At this point you will be able to activate the opener.
BATTERY: If the LED (light) on Transmitter does not turn on when a button is
pressed, repeat “changing the transmitter code” operation. If LED fails to light
replace battery. To change battery, insert a coin in the coin slot and twist
coin to access battery compartment. Use only 12-volt battery
